| 1 | ! L1=L2=4m, A1=20, A2=8, 2 dets |
|---|
| 2 | MASK/CLEAR |
|---|
| 3 | MASK/CLEAR/TIME |
|---|
| 4 | !PRINT start at 1.75 |
|---|
| 5 | L/WAV 1.75 15.5 0.05/LOG |
|---|
| 6 | ! adjusted to suit weak scatter |
|---|
| 7 | L/Q 0.0035,-.08,0.1,-.12,3.0 |
|---|
| 8 | ! strong scatter |
|---|
| 9 | !L/Q 0.0035 1.0 0.08/log |
|---|
| 10 | L/QXY 0 0.15 .002/lin |
|---|
| 11 | ! note increase lower time limit here |
|---|
| 12 | !BACK/MON/TIMES 85000 98000 |
|---|
| 13 | BACK/M2 85000 98000 |
|---|
| 14 | !check BACK/M4 |
|---|
| 15 | DET/REAR |
|---|
| 16 | GRAVITY/ON |
|---|
| 17 | ! |
|---|
| 18 | mask/rear h0 |
|---|
| 19 | mask/rear h190>h191 |
|---|
| 20 | mask/rear v0 |
|---|
| 21 | mask/rear v191 |
|---|
| 22 | mask/front h0 |
|---|
| 23 | mask/front h190>h191 |
|---|
| 24 | mask/front v0 |
|---|
| 25 | mask/front v191 |
|---|
| 26 | ! dead wire near top |
|---|
| 27 | mask/front h156>h159 |
|---|
| 28 | ! mask the added Cd over the hot spot |
|---|
| 29 | mask/front h53>h119+v150>v192 |
|---|
| 30 | ! |
|---|
| 31 | mask/time 13000 15250 |
|---|
| 32 | !mask/time 5000 19200 |
|---|
| 33 | !masking off beamstop arm 12mm wide at 19 degrees |
|---|
| 34 | mask/line 13 19 |
|---|
| 35 | ! |
|---|
| 36 | L/R 41 -1 3 |
|---|
| 37 | !L/Q/RCut 150 |
|---|
| 38 | !L/Q/WCut 14.0 |
|---|
| 39 | !PRINT RCut=150mm WCut=14 Ang |
|---|
| 40 | !L/SP 1 36864 |
|---|
| 41 | !MON/LENGTH=17.937 2 |
|---|
| 42 | ! |
|---|
| 43 | ! use this for rear |
|---|
| 44 | !MON/DIRECT=DIRECT_14225_4m_GC_M3trans_rear_03Aug12.dat |
|---|
| 45 | ! use for front, this command has to come second! |
|---|
| 46 | MON/TRANS/SPECTRUM=2/INTERPOLATE |
|---|
| 47 | TRANS/TRANSPEC=4/SHIFT=-70 |
|---|
| 48 | ! set monitor 2 to interpolate |
|---|
| 49 | MON/SPECTRUM=2/INTERPOLATE |
|---|
| 50 | PRINT fitting transmissions from 1.75 to 16.5 angstrom |
|---|
| 51 | FIT/TRANS/LOG 1.75 15.5 |
|---|
| 52 | !PRINT FIT/TRANS/OFF |
|---|
| 53 | !FIT/TRANS/OFF |
|---|
| 54 | ! |
|---|
| 55 | !30/07/12 GDW20 14271-add 8mm beam, assume same for 12mm |
|---|
| 56 | set centre -105.3 -165.8 |
|---|
| 57 | ! |
|---|
| 58 | !30/07/12 gdw20 14271-add, same scale seems good for 12mm beam, compared 1%w DTAB |
|---|
| 59 | set scales 0.1726 1.0 1.0 1.0 1.0 |
|---|
| 60 | ! correction to actual sample position, measured cryo at 320mm before shutter, notionally 81mm before shutter |
|---|
| 61 | ! DLS set up 81 - 132 =-34 |
|---|
| 62 | ! normal changer offset +53 |
|---|
| 63 | SAMPLE/OFFSET 53 |
|---|
| 64 | ! Correction to SANS2D encoders in mm |
|---|
| 65 | DET/CORR REAR X -16.0 |
|---|
| 66 | ! note rear Z was 58, but needs change all masks 9/11 on to 47 |
|---|
| 67 | DET/CORR REAR Z 47.0 |
|---|
| 68 | ! 7/8/12 front at 2.6m is at slightly too high Q values, was X -44 |
|---|
| 69 | DET/CORR FRONT X -24.0 |
|---|
| 70 | DET/CORR FRONT Y -20.0 |
|---|
| 71 | DET/CORR FRONT Z 47.0 |
|---|
| 72 | DET/CORR FRONT ROT 0.0 |
|---|
| 73 | ! (cf 115D Perkins) 80 is just inside window, 386 instead of DT's 306, but seems to work? , 48 should be central grid |
|---|
| 74 | DET/CORR FRONT RADIUS 48.0 |
|---|
| 75 | DET/CORR FRONT SIDE 0.0 |
|---|
| 76 | ! |
|---|
| 77 | !! 30/07/12 MASK122N 4m A1=20,A2=8, 2 dets, front rotated RKH |
|---|
