1 | SANS2D |
---|
2 | ! L1=L2=4m |
---|
3 | MASK/CLEAR |
---|
4 | MASK/CLEAR/TIME |
---|
5 | L/WAV 1.75 16.5 0.05/LOG |
---|
6 | ! adjusted to suit weak scatter |
---|
7 | L/Q 0.0035,0.001,0.0205,-.05,0.25,-.08,0.4,-.12,3.0 |
---|
8 | !L/Q 0.005,0.001,0.008,-0.08,1.0 |
---|
9 | ! weak scatter |
---|
10 | !L/Q 0.004, 0.004, 0.054, -0.12, 1.0 |
---|
11 | !L/Q 0.0035,0.002,0.04,-0.04,0.3,-.12,1.0 |
---|
12 | !L/Q 0.0035 1.0 0.08/log |
---|
13 | L/QXY 0 0.15 .002/lin |
---|
14 | ! note increase lower time limit here |
---|
15 | !BACK/MON/TIMES 85000 98000 |
---|
16 | BACK/M2 85000 98000 |
---|
17 | !check BACK/M4 |
---|
18 | DET/REAR |
---|
19 | GRAVITY/ON |
---|
20 | ! |
---|
21 | mask/rear h0 |
---|
22 | mask/rear h190>h191 |
---|
23 | mask/rear v0 |
---|
24 | mask/rear v191 |
---|
25 | mask/front h0 |
---|
26 | mask/front h190>h191 |
---|
27 | mask/front v0 |
---|
28 | mask/front v191 |
---|
29 | ! front: dead wire near top |
---|
30 | mask/front h156>h159 |
---|
31 | ! rear: dead wire towards top - fixed |
---|
32 | !mask/rear h166>h173 |
---|
33 | ! spot on top b/s when hit meniscus ??? |
---|
34 | !mask h72>h75+v117>v122 |
---|
35 | ! |
---|
36 | mask/time 13000 16250 |
---|
37 | PRINT masking off beamstop arm 13mm wide at 20 degrees |
---|
38 | !PRINT not masking beam stop arm, M4 out |
---|
39 | mask/line 13 20 |
---|
40 | ! |
---|
41 | L/R 41 -1 3 |
---|
42 | !L/SP 1 36864 |
---|
43 | !MON/LENGTH=17.937 2 |
---|
44 | ! |
---|
45 | ! use this for rear |
---|
46 | MON/DIRECT=DIRECT_16246_4m_Rear_17Dec12.dat |
---|
47 | ! use for front, this command has to come second! |
---|
48 | MON/DIRECT/FRONT=DIRECT_6958_4m_rescaled_09Mar12.dat |
---|
49 | MON/TRANS/SPECTRUM=2/INTERPOLATE |
---|
50 | TRANS/TRANSPEC=4/SHIFT=-70 |
---|
51 | !TRANS/TRANSPEC=3 |
---|
52 | ! set monitor 2 to interpolate |
---|
53 | MON/SPECTRUM=2/INTERPOLATE |
---|
54 | FIT/TRANS/LOG 1.75 16.5 |
---|
55 | !PRINT FIT/TRANS/OFF |
---|
56 | !FIT/TRANS/OFF |
---|
57 | ! |
---|
58 | ! 12/12/13 scale & centre from GDW20 22668 |
---|
59 | set centre -106.1 -169.15 |
---|
60 | ! |
---|
61 | set scales 0.1620 1.0 1.0 1.0 1.0 |
---|
62 | ! correction to actual sample position, measured cryo at 320mm before shutter, notionally 81mm before shutter |
---|
63 | ! DLS set up 81 - 133 =-52 |
---|
64 | ! normal changer offset +53 |
---|
65 | ! rotating rack 100mm before shutter = 81 - 100 = -19 |
---|
66 | ! old rotating rack 131mm before shutter = 81 - 131 = -50 |
---|
67 | ! linkam 42mm before shutter = 81 - 42 = 39 |
---|
68 | SAMPLE/OFFSET 53 |
---|
69 | ! Correction to SANS2D encoders in mm |
---|
70 | DET/CORR REAR X -16.0 |
---|
71 | ! note rear Z was 58, but needs change all masks 9/11 on to 47 |
---|
72 | DET/CORR REAR Z 47.0 |
---|
73 | ! 7/8/12 front at 2.6m is at slightly too high Q values, was X -44 |
---|
74 | DET/CORR FRONT X -24.0 |
---|
75 | DET/CORR FRONT Y -20.0 |
---|
76 | DET/CORR FRONT Z 47.0 |
---|
77 | DET/CORR FRONT ROT 0.0 |
---|
78 | ! (cf 115D Perkins) 80 is just inside window, 386 instead of DT's 306, but seems to work? , 48 should be central grid |
---|
79 | DET/CORR FRONT RADIUS 48.0 |
---|
80 | DET/CORR FRONT SIDE 0.0 |
---|
81 | ! |
---|
82 | !! 12/12/13 MASK134E 4m A1=20,A2=6, Dreiss Sample Changer |
---|